Mixer Tap Installation Fish Hoek | Kitchen & Bathroom Taps

About Mixer Tap Installation in Fish Hoek

A mixer tap blends hot and cold water through a single spout, giving you precise temperature control. Modern mixer taps are available in dozens of styles - from sleek minimalist kitchen taps with pull-out spray heads to classic cross-handle bathroom basin mixers. Regardless of the style, correct installation is essential for leak-free operation and proper water flow.

At Abacas Solution, we install mixer taps for basins, baths, kitchen sinks, and shower valves in Fish Hoek homes and commercial properties. The installation process involves removing the old tap (which often requires dealing with corroded or seized connections underneath the basin or sink), fitting the new mixer tap through the tap hole, connecting flexible supply hoses to the isolation valves, and testing for leaks at every joint.

One of the most common issues we encounter during mixer tap installations in South African homes is incompatible plumbing. Many older homes have separate hot and cold taps with individual supply pipes spaced apart. Converting to a single-hole mixer tap may require adapting the supply lines, adding a tap converter plate, or modifying the basin or sink. We handle these modifications as part of the installation.

We also replace ceramic disc cartridges in existing mixer taps that drip or are difficult to operate. In many cases, a R100-R300 cartridge replacement restores a mixer tap to perfect function, avoiding the cost of a complete tap replacement.

This is one of several specialist services we offer under bathroom & kitchen plumbing in Fish Hoek. As part of our Fish Hoek plumbing team, we bring over 25 years of hands-on experience to every job.

Mixer Tap Installation in Fish Hoek - Abacas Solution

When to Call for Mixer Tap Installation

Call when you want to replace an old or dripping tap with a new mixer, when you are upgrading from separate hot and cold taps to a single mixer, when your tap handle is stiff or difficult to turn, when there is a constant drip from the spout even when closed, or when you have purchased a new tap and need it professionally fitted.

Our Mixer Tap Installation Process

1

Tap Selection Advice

Call 067 071 9472. If you have already purchased a tap, confirm it is compatible with your basin or sink tap holes. If you need help choosing, we advise on styles, brands, and compatibility with your existing plumbing configuration.

2

Old Tap Removal

We isolate the water supply, disconnect and remove the old tap. Corroded or seized nuts underneath basins and sinks are carefully released using basin wrenches and penetrating oil to avoid damaging the porcelain or stainless steel.

3

New Tap Fitting

We fit the new mixer tap through the tap hole with the correct gasket and washer, tighten the fixing nut from below, connect new braided flexible hoses to the hot and cold isolation valves, and ensure all connections are firm without over-tightening.

4

Test & Adjust

We turn on both hot and cold supply, check for leaks at every connection point under pressure, verify smooth handle operation, confirm adequate flow rate, and check that the swivel (on kitchen taps) moves freely without stiffness.

Many homeowners in Fish Hoek who need mixer tap installation also require basin installation in Fish Hoek and bath installation. We handle everything, so you only need one call.

Safety & Compliance

Always ensure isolation valves are fitted below the basin or sink so the tap can be serviced without shutting off the entire household water supply. In South Africa, hot water should always be connected to the left-hand side when facing the tap - this is both convention and a safety consideration. Use only approved flexible hoses rated for the mains pressure in your area. Low-quality braided hoses are a common cause of burst connections and water damage.

Mixer Tap Installation Cost in Fish Hoek

Mixer tap installation labour costs R300-R600 depending on accessibility and whether pipe modifications are needed. A straightforward tap swap where the new mixer fits the existing tap hole costs R300-R400. If supply lines need adapting from separate hot/cold to a single mixer, add R200-R500. Fitting a kitchen mixer with pull-out spray costs R400-R600 due to the additional spray hose routing. New isolation valves cost R150-R300 per pair if not already fitted. Mixer taps themselves range from R300 for budget models to R3,000-R8,000 for premium brands.

Frequently Asked Questions

Can I replace two separate taps with a single mixer tap?

Usually yes, but it depends on the basin or sink. If your basin has a single centre tap hole, a standard mixer fits directly. If it has two separate tap holes, you can use a mixer tap with a mounting plate that covers both holes, or choose a three-hole mixer with separate handles. We assess your situation and recommend the best approach.

How much does it cost to fit a mixer tap in Fish Hoek?

Labour to fit a mixer tap in Fish Hoek is R300-R600. A straightforward swap where the new tap fits the existing hole is R300-R400. If pipe modifications are needed, the cost increases. The tap itself is separate - you can supply your own or we can source one for you. Budget taps start around R300, while quality mid-range taps are R800-R2,000.

My mixer tap drips. Does it need replacing?

Not necessarily. Most mixer taps use ceramic disc cartridges that wear out over time. Replacing the cartridge costs R100-R300 for the part plus labour, and restores the tap to like-new operation. We stock common cartridge sizes. If the tap body is corroded or the finish is deteriorating, then replacement makes more sense.

What brand of mixer tap do you recommend?

For durability and value in the South African market, we recommend Hansgrohe, Grohe, and Cobra for mid-range quality. For budget-friendly options, Builders Warehouse own-brand and Comap taps offer reasonable quality. For premium kitchens and bathrooms, Franke, Blanco, and Dornbracht are excellent. We advise based on your budget and intended use.